JKAerotech Mig 3 build

Discussion about electric combat competition and combat model design and construction.

JKAerotech Mig 3 build

New postby AndrewS on Mon Sep 23, 2013 4:20 pm

Hi guys,
I started on building my combat Mig today.
Step 1 was cut the tail feathers free of the chloroplast sheet. Wasn't too hard as they were mostly cut through from the store. Then you cut just the bottom surface of the horizontal stab and remove one rib. This makes the hinge for the elevator. Then insert the horizontal stab into the vertical stab and glue using Goop or thick ca(I didn't have any goop).
I spray glued the fire wall pattern to the supplied wood and cut it out with my bandsaw.
I then tack glued it to the front of the fuselage.
That's it so far. I'll update as I go.

Andrew
Attachments
20130923_155743(0).jpg
20130923_154035.jpg
20130923_152745.jpg
20130923_150820.jpg
20130923_150814.jpg
Andrew Smith,
HEFA 3
MAAC 76250
User avatar
AndrewS
 
Posts: 788
Joined: Thu Oct 02, 2008 8:23 am
Location: Bedford, Nova Scotia

Re: JKAerotech Mig 3 build

New postby AndrewS on Mon Sep 23, 2013 4:26 pm

Here's the firewall on the fuse.
Attachments
20130923_160447.jpg
Firewall spray tacked to fuselage
Andrew Smith,
HEFA 3
MAAC 76250
User avatar
AndrewS
 
Posts: 788
Joined: Thu Oct 02, 2008 8:23 am
Location: Bedford, Nova Scotia

Re: JKAerotech Mig 3 build

New postby david3484 on Mon Sep 23, 2013 8:21 pm

Looking good there Andrew!
Dave M

Halifax Electric Flyers Association (HEFA) # 079
MAAC # 84499
DX8
User avatar
david3484
 
Posts: 356
Joined: Wed Jun 15, 2011 11:25 am
Location: Cole Harbour

Re: JKAerotech Mig 3 build

New postby CF Av8or on Mon Sep 23, 2013 9:50 pm

Thanks for doing this build log, Andrew. Looks good so far!

What thickness of coroplast are the tail feathers? Looks like it might be 3 mm, which I really wish was available to us here in the Maritimes!

Vic
User avatar
CF Av8or
 
Posts: 741
Joined: Sat Mar 28, 2009 9:10 am
Location: East Lawrencetown

Re: JKAerotech Mig 3 build

New postby AndrewS on Mon Sep 23, 2013 10:09 pm

Actually Vic, it's 4mm.
Have to pick up a roll of fibre tape tomorrow.
Andrew
Andrew Smith,
HEFA 3
MAAC 76250
User avatar
AndrewS
 
Posts: 788
Joined: Thu Oct 02, 2008 8:23 am
Location: Bedford, Nova Scotia

Re: JKAerotech Mig 3 build

New postby retiredVTT on Tue Sep 24, 2013 12:25 am

Andrew, I saw 3/4" fibre strapping tape at CTC, Bedford, last week...

Bill
Bill
HEFA #5
MAAC #13708
User avatar
retiredVTT
 
Posts: 5086
Joined: Wed Oct 01, 2008 9:59 pm
Location: Bedford, NS

Re: JKAerotech Mig 3 build

New postby CF Av8or on Tue Sep 24, 2013 6:59 am

Andrew,

If you're looking for the wider strapping tape, I would suggest the 2" wide 3M rolls available at Staples. They are more expensive than most, but the quality is top notch and it applies beautifully. I use it exclusively on my slope-soaring warbird foamies.

Vic
User avatar
CF Av8or
 
Posts: 741
Joined: Sat Mar 28, 2009 9:10 am
Location: East Lawrencetown

Re: JKAerotech Mig 3 build

New postby AndrewS on Tue Sep 24, 2013 7:49 am

Bill, Vic thanks for the tape info. I'll probably get some of both sizes.
Andrew
Andrew Smith,
HEFA 3
MAAC 76250
User avatar
AndrewS
 
Posts: 788
Joined: Thu Oct 02, 2008 8:23 am
Location: Bedford, Nova Scotia

Re: JKAerotech Mig 3 build

New postby Nathan on Tue Nov 26, 2013 11:23 pm

How is this build going. How did you like ordering from JKA?
Nathan
 
Posts: 1
Joined: Tue Nov 26, 2013 3:21 pm


Return to Combat

Who is online

Users browsing this forum: No registered users and 1 guest